Do Plumbers Fix Garbage Disposals?

Are you curious about whether you need to hire a plumber to fix your garbage disposals? If you’re like most homeowners, you don’t know how to repair your own kitchen sink, so you want to find out as much information as possible before making a decision. You should also learn about the common problems that cause your garbage disposal to break down.
Repairing a leaky garbage disposal

When you have a leaky garbage disposal, it can be a hassle and can cause damage to your kitchen. It is important to find out where the leak is coming from before you can begin repairing it.

One of the most common sources of a garbage disposal leak is the sink flange. This is a metal piece that fits inside the drain hole in the center of your sink. Over time, this can weaken or break and result in a leak.

You can easily fix this problem by resealing the flange. Normally, this is done with plumber’s putty. However, over time, this putty can become weakened or break. If you are not experienced with this repair, it may be best to have a professional take care of the job for you.
Replacing a gasket 1

If you’ve noticed that your garbage disposal is leaking, there’s a simple solution. A new rubber gasket should fix the problem and can be installed in fifteen minutes.

Before you do any work, however, it’s important to remove the disposal from your sink. This is usually done by unscrewing three screws. Alternatively, you can hire a professional to perform the job.

Next, disconnect the garbage disposal from the power and breaker box. It may also be necessary to shut off the wall outlet. After that, you should plug the disposal back in.

You can test to see if it’s leaking by turning the disposal on and off several times. Inspect the motor to see if it’s making any noises. Some models have a reset button, which will help stop the unit if it begins to vibrate.
Replacing a flywheel

If you have a garbage disposal that is not working properly, it may have a stuck flywheel. To repair a garbage disposal that has a stuck flywheel, you should follow the manufacturer’s instructions.

To start fixing a flywheel that is stuck, you should first turn off the power to the disposal. You can do this by turning off the switch at the electrical service panel.

Once you turn off the power to the disposal, you should remove the disposal from the cabinet. You should also unplug the unit from its support ring.

Then you can free the flywheel. For this, you will need to use a hex wrench. This will allow you to turn the flywheel manually.

Alternatively, you can use a wooden spoon. Using a wooden spoon can help you visualize where the jam is located.
Common problems with garbage disposals

If your garbage disposal is making strange noises, you should call a plumber to look into the issue. It is possible that the problem is in the disposal itself or with the electrical wires.

If you hear a loud, grinding noise when you run your disposal, the blades may have become jammed. This can also cause clogging. free tools and services can be used to push against the blades to free the jam.

Another common problem with garbage disposals is that they leak. Sometimes they leak at the top, side, or bottom of the unit. The best way to prevent this is to not toss large chunks of food into the disposal. Other causes include clogs or not running enough water.

If you have a hardwired garbage disposal, you should first check the wiring to see if it is plugged in correctly. Otherwise, you might need to replace the disposal or the entire unit.
Finding the right size for your kitchen sink

Choosing the wrong size for your kitchen sink can be a big mistake. It can leave you with problems in terms of maintenance and cleaning. Also, the wrong size can scare off potential home buyers.

The correct size is usually somewhere between 22 and 24 inches. This will allow you to accommodate large pots and pans without clogging the drain. However, it also requires you to consider the space you have available on your countertop.


You should also check the depth of the sink. A shallower sink will require less space than a deeper one. If you’re not sure, you can hire a handyman to confirm.

You should also measure the space under your cabinet. You want to make sure there is plenty of room to install your new sink.

Candu Plumbing & Rooter
22144 Eccles St, Canoga Park, CA 91304
(855) 522-2638
https://www.canduplumbing.com/